Skip to content
DEWALT

Acorn Nut Sleeve Anchor, 1/4" × 1-3/8", Zinc-Plated Carbon Steel, 100-Pack - Each

0 Reviews
SKU
05150 - EACH

The DEWALT acorn-nut sleeve anchor is a preassembled 1/4 in. × 1-3/8 in. zinc-plated carbon-steel anchor supplied in a 100-pack. Its specified base materials include normal-weight concrete, grouted or hollow CMU, brick masonry, and stone.

  • 1/4 in. × 1-3/8 in. size
  • Concrete and masonry base materials
  • Zinc-plated carbon steel
  • 100-anchor package
  • Preassembled single-unit design
  • 360° sleeve contact coverage

Product Overview

The DEWALT acorn-nut sleeve anchor is a preassembled 1/4 in. × 1-3/8 in. zinc-plated carbon-steel anchor supplied in a 100-pack. Its specified base materials include normal-weight concrete, grouted or hollow CMU, brick masonry, and stone.

Technical Specifications

Product information and specifications for the selected item.

SKU: 05150 - EACH

Product Information

BrandDEWALT
MPN05150 - EACH
SKU05150 - EACH
CategoryFasteners & Hardware

Key Specs

Fastener TypeSleeve Anchors
Fastener MaterialSteel
Fastener PlatingZinc

Capacity & Fastener

Fastener TypeSleeve Anchors
Fastener MaterialSteel
Sleeve contact coverage360 degrees
Minimum plow-bolt yield strength53,700 psi
Expansion sleeve steel gradeAISI 1010
Plow bolt thread size10-24 UNC
Assembly statePreassembled
Plow bolt steel gradeAISI 1018
Assembly configurationPre-assembled, single-unit sleeve anchor

Finish & Use

Fastener PlatingZinc
Measurement SystemInches
Tightening methodTurn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position
Acorn-nut installation sequencePlace washer on anchor and thread on nut; drive through the fixture until the nut and washer are firmly seated against it at the required embedment depth
Guide installation torque at 1/2-in minimum embedment in normal-weight concrete2 ft-lb
Drill-bit tolerance standardDrill-bit tolerances must meet ANSI Standard B212.15
Suitable base materialsNormal-weight concrete; grouted or hollow concrete masonry (CMU); brick masonry; stone
Coating specificationASTM B633, SC1, Type III (Fe/Zn 5)
Anchor seating procedurePosition the washer and thread on the nut; drive the anchor through the fixture until the nut and washer are firmly seated and the required embedment depth is reached
Solid clay brick table parametersAt f’m ≥ 1,500 psi: 1-in minimum embedment; 4-ft-lb guide torque; 4-in minimum edge distance; 1-1/2-in minimum end distance
Hollow/solid CMU table parameters1-in minimum embedment; 4-ft-lb guide torque; 3-3/4-in minimum edge distance; 4-in minimum end distance
Tightening procedureTurn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position
Hole cleaningRemove dust and debris during drilling or afterward using a dust extractor or hollow bit, suction, or forced air

Dimensions & Weight

Fixture clearance hole5/16 in
Drill-hole depthAt least 1/2 in or one anchor diameter deeper than the required embedment
Required drill-bit diameter1/4 in.
ANSI drill bit size1/4 in
Drilled-hole depthAt least 1/2 in, or one anchor diameter deeper than the required embedment
Wrench size3/8 in

Product Documents

  • Lok-Bolt AS® Sleeve Anchor — Technical Guide – Mechanical Anchors (Rev. D, 2025) Spec sheet Open / download file

Your cart

0 products 0 units

Your cart is empty.

Add products as you browse, then review them here.