Skip to content

Generac Next Gen 150A 1-Phase 120/240V Service-Entrance-Rated Automatic Transfer Switch, NEMA 3R, No SPD

0 Reviews
SKU
9932

Generac 9932 is a UL Listed, 150 A automatic transfer switch for single-phase 120/240 V optional standby systems. It is service-entrance rated, has a NEMA 3R enclosure, is non-fused, and does not include an SPD; compatibility is specified for single-phase generators using Evolution™ or Power Zone™ 200 controllers.

  • 150 A Maximum Rating
  • Single-Phase 120/240 V
  • Service-Entrance Rated
  • Automatic Transfer Operation
  • NEMA 3R Enclosure
  • No SPD Included

Product Overview

Generac 9932 is a UL Listed, 150 A automatic transfer switch for single-phase 120/240 V optional standby systems. It is service-entrance rated, has a NEMA 3R enclosure, is non-fused, and does not include an SPD; compatibility is specified for single-phase generators using Evolution™ or Power Zone™ 200 controllers.

Technical Specifications

Product information and specifications for the selected item.

SKU: 9932

Product Information

BrandGenerac
MPN9932
SKU9932
CategoryAutomatic Transfer Switches

Key Specs

Maximum Amperage (A)150
FusedNon-Fused
Automatic/ManualAutomatic
Certifications and ListingsUL Listed

Electrical Ratings

Maximum Amperage (A)150
FusedNon-Fused
Generator control wiringNo. 18 AWG minimum, up to 500 ft (152.4 m); copper conductors only
Transfer terminal tightening torque275 in-lbs (31 Nm)
Auxiliary contact rating10 A at 125 or 250 VAC; 0.6 A at 125 VDC
Service Breaker ConfigurationIncludes a utility service circuit breaker
Combined load limitCombined motor full-load amperes and other load amperes must not exceed the switch rating
Utility service circuit breaker frequency50/60 Hz
Control circuit classificationClass 1 signaling circuit
Maximum tungsten load30 % of switch rating
Transfer mechanism conductor range#6-250 MCM (Cu/Al)
Neutral-ground bonding jumperJumper bonds the ground-neutral lug; remove it if the switch is not used as service equipment
Lug Range250 MCM - #6
Withstand Rating22,000 A

Transfer & Features

Automatic/ManualAutomatic
FeaturesMountable, Water Resistant
Enclosure environmental protectionProvides a degree of protection against falling rain and sleet; ice formation does not damage the enclosure
Load Transition TypeOpen transition
Service-equipment installationMay be installed as service equipment or not as service equipment
Generator Controller CompatibilitySingle-phase generators using Evolution™ or Power Zone™ 200 controllers
Compatible load typesMotors, electric-discharge lamps, tungsten-filament loads, and electric-heating equipment
Neutral conductor behaviorNeutral connects to a neutral lug and is not switched
Mounting environmentIndoor or outdoor mounting
Power terminal constructionSolderless, screw-type terminal lugs
Intended applicationOptional standby systems only (NEC Article 702)

Certifications

Certifications and ListingsUL Listed

Dimensions & Weight

Height (in.)30
Width (in.)13.5
Length (in.)6.3
Weight (lb.)30
Mounting hole spacing10.5 in. (266.7 mm)
Mounting orientationMount upright on a vertical rigid supporting structure
Conduit knockout sizes1-1/2 and 2 in. conduit

Product Documents

  • Installation Drawing—150A/200A SE Install with Cleat, No. A0006058193-B Drawing photometric Open / download file
  • Generac Power Systems Limited 5 Year (5M) Warranty for Stationary Transfer Switch Systems, Part No. 0K9470, Rev. F (03/06/2023) Warranty Open / download file
  • Owner’s Manual — Automatic Transfer Switch, 100–200 Amp, Service Entrance and Non-Service Entrance with Surge Protection Device (SPD), Part No. A0005959486, Rev. A (02/04/2025) Manual Open / download file

Your cart

0 products 0 units

Your cart is empty.

Add products as you browse, then review them here.