Skip to content
Powers Fasteners

Lok/Bolt Hex Nut Sleeve Anchor, 1/2 x 2-1/4 in.

0 Reviews
SKU
05025-EACH

Lok/Bolt Hex Nut Sleeve Anchor, 1/2 x 2-1/4 in.Additional specifications Additional specifications · Construction Vibration resistance The flexible compression ring helps resist loosening under vibratory loads Assembly construction Pre-assembled as a single unit Compression ring material Nylon Expansion locking mechanism Under load, the tapered p...

Needs Data

Lok/Bolt Hex Nut Sleeve Anchor, 1/2 x 2-1/4 in.Additional specifications Additional specifications · Construction Vibration resistance The flexible compression ring helps resist loosening under vibratory loads Assembly construction Pre-assembled as a single unit Compression ring material Nylon Expansion locking mechanism Under load, the tapered p...

Product Overview

Lok/Bolt Hex Nut Sleeve Anchor, 1/2 x 2-1/4 in.

Additional specifications

Additional specifications · Construction

Vibration resistance The flexible compression ring helps resist loosening under vibratory loads
Assembly construction Pre-assembled as a single unit
Compression ring material Nylon
Expansion locking mechanism Under load, the tapered plow bolt advances into the expansion sleeve to increase locking action against the hole walls
Sleeve contact design 360° contact area that reduces concrete stress

Additional specifications · Installation

Hole preparation Clean dust and other material from the hole; do not expand the anchor before installation
ANSI drill bit size for this anchor 1/2 in
Tightening procedure Tighten 3 to 5 turns past finger-tight, or apply the guide installation torque from the finger-tight position
Seating procedure Drive through the fixture until the head is firmly seated and the required embedment depth is reached
Wrench size 9/16 in
Maximum tightening torque for the carbon-steel 1/2-in anchor in normal-weight concrete 20-28 ft-lb
Fixture clearance hole for this anchor 9/16 in
Catalog minimum embedment 2 1/8 in
Drill-bit tolerance standard Drill-bit tolerances should meet ANSI Standard B212.15
Hole-depth requirement Drill at least 1/2 in or one anchor diameter deeper than the required embedment
Maximum tightening torque for the carbon-steel size 20-28 ft-lb
Plow bolt thread size 3/8-16 UNC

Additional specifications · Compliance

Factory Mutual approval FM Approvals Serial No. 26692; J.I. OJ8A1.AH and J.I. OJ9A9.AH

Additional specifications · Materials

Hex nut component specification ASTM A 563, Grade A
Washer component specification ASTM F 844

Additional specifications · Compatibility

General compatible substrates Concrete, block, brick, and stone
Fixture-hole compatibility Fits standard fixture holes; undersizing is not required for proper fit
Specified base-material types Normal-weight concrete; structural lightweight concrete; grouted concrete masonry; hollow concrete masonry

Additional specifications · Applications

Typical applications Door and window frames; wall fixtures; handrails and fencing; shelving and storage; masonry applications; electrical and mechanical attachments

Technical Specifications

Product information and specifications for the selected item.

SKU: 05025-EACH

Product Information

BrandPowers Fasteners
MPN05025-EACH
SKU05025-EACH
CategoryFasteners & Hardware

Key Specs

Weight Capacity (lb.)Greater than 450
Fastener TypeSleeve Anchors
Fastener MaterialSteel
Fastener PlatingElectro Galvanized Zinc

Capacity & Fastener

Weight Capacity (lb.)Greater than 450
Fastener TypeSleeve Anchors
Fastener MaterialSteel
Vibration resistanceThe flexible compression ring helps resist loosening under vibratory loads
Hex nut component specificationASTM A 563, Grade A
Assembly constructionPre-assembled as a single unit
Maximum tightening torque for the carbon-steel 1/2-in anchor in normal-weight concrete20-28 ft-lb
Compression ring materialNylon
Expansion locking mechanismUnder load, the tapered plow bolt advances into the expansion sleeve to increase locking action against the hole walls
Sleeve contact design360° contact area that reduces concrete stress
Washer component specificationASTM F 844
Maximum tightening torque for the carbon-steel size20-28 ft-lb
Plow bolt thread size3/8-16 UNC

Finish & Use

Fastener PlatingElectro Galvanized Zinc
Measurement SystemInches
Hole preparationClean dust and other material from the hole; do not expand the anchor before installation
Factory Mutual approvalFM Approvals Serial No. 26692; J.I. OJ8A1.AH and J.I. OJ9A9.AH
Tightening procedureTighten 3 to 5 turns past finger-tight, or apply the guide installation torque from the finger-tight position
Seating procedureDrive through the fixture until the head is firmly seated and the required embedment depth is reached
General compatible substratesConcrete, block, brick, and stone
Fixture-hole compatibilityFits standard fixture holes; undersizing is not required for proper fit
Specified base-material typesNormal-weight concrete; structural lightweight concrete; grouted concrete masonry; hollow concrete masonry
Typical applicationsDoor and window frames; wall fixtures; handrails and fencing; shelving and storage; masonry applications; electrical and mechanical attachments

Dimensions & Weight

ANSI drill bit size for this anchor1/2 in
Wrench size9/16 in
Fixture clearance hole for this anchor9/16 in
Catalog minimum embedment2 1/8 in
Drill-bit tolerance standardDrill-bit tolerances should meet ANSI Standard B212.15
Hole-depth requirementDrill at least 1/2 in or one anchor diameter deeper than the required embedment

Your cart

0 products 0 units

Your cart is empty.

Add products as you browse, then review them here.