Skip to content
DEWALT

Lok/Bolt Hex Nut Sleeve Anchor, 3/8 x 3 in.

0 Reviews
SKU
05020-EACH

Lok/Bolt Hex Nut Sleeve Anchor, 3/8 x 3 in.Additional specifications Additional specifications · Compliance Drill-bit tolerance standard ANSI Standard B212.15 Additional specifications · Installation Tightening procedure Turn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position Guide in...

Needs Data

Lok/Bolt Hex Nut Sleeve Anchor, 3/8 x 3 in.Additional specifications Additional specifications · Compliance Drill-bit tolerance standard ANSI Standard B212.15 Additional specifications · Installation Tightening procedure Turn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position Guide in...

Product Overview

Lok/Bolt Hex Nut Sleeve Anchor, 3/8 x 3 in.

Additional specifications

Additional specifications · Compliance

Drill-bit tolerance standard ANSI Standard B212.15

Additional specifications · Installation

Tightening procedure Turn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position
Guide installation torque in normal-weight concrete (carbon steel) 18 ft-lb
Drilled-hole depth Drill at least 1/2 in. or one anchor diameter deeper than the required embedment
Placement condition for normal-weight concrete data Minimum anchor spacing and edge distance of 12 times the anchor diameter
Washer-and-nut seating procedure Place the washer on the anchor and thread on the nut; drive through the fixture until the nut and washer are firmly seated against the fixture and the anchor reaches required embedment
Hole cleaning Remove dust and debris during drilling or after drilling to extract loose particles
ANSI drill bit size for 3/8-in. anchor 3/8 in
Wrench size for 3/8-in. anchor 1/2 in
Minimum edge and end distances in solid clay brick Minimum edge distance 8; minimum end distance 8
Placement condition for masonry data Minimum spacing between anchors of 16 times the anchor diameter
Minimum edge and end distances in concrete masonry Minimum edge distance 3-3/4; minimum end distance 4
Minimum embedment in concrete masonry 1-1/4 in
Guide installation torque in solid clay brick 15 ft-lb
Minimum embedment in solid clay brick 1-1/4 in
Guide installation torque in concrete masonry 15 ft-lb
Plow bolt thread size 5/16-18 UNC
Minimum embedment in normal-weight concrete 1-1/4 in
Fixture clearance hole for 3/8-in. anchor 7/16 in

Additional specifications · Compatibility

Concrete masonry substrate criteria Minimum 6-in.-wide, Grade N, Type II normal-weight CMUs conforming to ASTM C90; Type N, S, or M mortar; masonry prism strength at least 1,500 psi at installation
Suitable base materials Normal-weight concrete; grouted concrete masonry (CMU); hollow concrete masonry (CMU); brick masonry; stone
Solid clay brick substrate criteria Grade SW, minimum two-wythe solid clay brick conforming to ASTM C62; Type N, S, or M mortar; f'm at least 1,500 psi

Additional specifications · Material

Plow bolt material grade AISI 1018
Plow bolt minimum yield strength 53,700 psi

Technical Specifications

Product information and specifications for the selected item.

SKU: 05020-EACH

Product Information

BrandDEWALT
MPN05020-EACH
SKU05020-EACH
CategoryFasteners & Hardware

Key Specs

Fastener TypeSleeve Anchors
Fastener MaterialSteel
Fastener PlatingZinc

Capacity & Fastener

Fastener TypeSleeve Anchors
Fastener MaterialSteel
Guide installation torque in normal-weight concrete (carbon steel)18 ft-lb
Plow bolt material gradeAISI 1018
Guide installation torque in solid clay brick15 ft-lb
Guide installation torque in concrete masonry15 ft-lb
Plow bolt thread size5/16-18 UNC
Plow bolt minimum yield strength53,700 psi

Finish & Use

Fastener PlatingZinc
Measurement SystemInches
Drill-bit tolerance standardANSI Standard B212.15
Tightening procedureTurn the nut or head 3 to 5 turns past finger tight, or apply guide installation torque from the finger-tight position
Concrete masonry substrate criteriaMinimum 6-in.-wide, Grade N, Type II normal-weight CMUs conforming to ASTM C90; Type N, S, or M mortar; masonry prism strength at least 1,500 psi at installation
Washer-and-nut seating procedurePlace the washer on the anchor and thread on the nut; drive through the fixture until the nut and washer are firmly seated against the fixture and the anchor reaches required embedment
Hole cleaningRemove dust and debris during drilling or after drilling to extract loose particles
Suitable base materialsNormal-weight concrete; grouted concrete masonry (CMU); hollow concrete masonry (CMU); brick masonry; stone
Solid clay brick substrate criteriaGrade SW, minimum two-wythe solid clay brick conforming to ASTM C62; Type N, S, or M mortar; f'm at least 1,500 psi

Dimensions & Weight

Drilled-hole depthDrill at least 1/2 in. or one anchor diameter deeper than the required embedment
Placement condition for normal-weight concrete dataMinimum anchor spacing and edge distance of 12 times the anchor diameter
ANSI drill bit size for 3/8-in. anchor3/8 in
Wrench size for 3/8-in. anchor1/2 in
Minimum edge and end distances in solid clay brickMinimum edge distance 8; minimum end distance 8
Placement condition for masonry dataMinimum spacing between anchors of 16 times the anchor diameter
Minimum edge and end distances in concrete masonryMinimum edge distance 3-3/4; minimum end distance 4
Minimum embedment in concrete masonry1-1/4 in
Minimum embedment in solid clay brick1-1/4 in
Minimum embedment in normal-weight concrete1-1/4 in
Fixture clearance hole for 3/8-in. anchor7/16 in

Your cart

0 products 0 units

Your cart is empty.

Add products as you browse, then review them here.