586-554-2000
Mon–Fri 6:30am–5pm · Sat 8am–3pm
586-554-2000
Mon–Fri 6:30am–5pm
Close
Menu
Services we offer
Jobsite Delivery
Free delivery on $250+ orders within 25 miles.
Will Call Pickup
Order ahead and pick up at our Warren or Waterford branch.
Wire Cutting & Paralleling
Custom cuts and paralleled runs to your lengths.
Project Takeoffs & Estimating
Send your plans. We count and price the materials.
Scissor Lift Rentals
Lift rentals for overhead lighting and electrical work.
Material Staging & Kitting
Materials staged and kitted to save time on site.
And many more
Long Lag Screw Shield Anchor, 1/4 in.Additional specifications Additional specifications · Compatibility Lag screw thread size 1/4-10 UNC Compatible lag-screw thread 1/4-10 UNC Compatible substrates Concrete and mortar joints of brick and block walls Suitable base materials Concrete, masonry, and mortar joints Thread length 1 in. Additional...
Needs Data
Long Lag Screw Shield Anchor, 1/4 in.Additional specifications Additional specifications · Compatibility Lag screw thread size 1/4-10 UNC Compatible lag-screw thread 1/4-10 UNC Compatible substrates Concrete and mortar joints of brick and block walls Suitable base materials Concrete, masonry, and mortar joints Thread length 1 in. Additional...
Long Lag Screw Shield Anchor, 1/4 in.
| Lag screw thread size | 1/4-10 UNC |
|---|---|
| Compatible lag-screw thread | 1/4-10 UNC |
| Compatible substrates | Concrete and mortar joints of brick and block walls |
| Suitable base materials | Concrete, masonry, and mortar joints |
| Thread length | 1 in. |
| Federal specification | GSA FFS-325C, Group 2, Type 1, Class 1 (long) |
|---|
| Recommended substrate condition | Long version recommended for soft or weak masonry to add strength to the substrate |
|---|
| Anchor seating | Insert the anchor into the hole and tap flush |
|---|---|
| Anchor setting | Insert the anchor into the hole and tap flush. |
| Hole drilling procedure | Drill perpendicular to the work surface; do not ream the hole or allow the drill to wobble. |
| Hole depth and clearance | Drill at least one anchor diameter deeper than the intended embedment, but no closer than two diameters to the opposite concrete surface. |
| Drill bit requirement | Use solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards. |
| Installation safety | Wear safety glasses and follow the drill manufacturer's instructions. |
| Fixture fastening | Position the fixture, insert the bolt, and tighten. |
| Hole cleaning | Clean the hole with a nylon brush and compressed air. |
| Installation torque | Approximately 5 ft.-lbs. |
| Drill bit standard | Use solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards |
| Drill bit diameter | 1/2 in. |
| Threading and removability | Internally threaded; allows bolt removal for service work |
|---|---|
| Corrosion resistance | Corrosion resistant |
| Removability and service | Internal threading allows easy bolt removal and service work. |
| Substrate recommendation | The long version is recommended for soft or weak masonry to add strength to the substrate. |
|---|---|
| Listed application | Railings |
Product information and specifications for the selected item.
| Brand | EMC FASTEN |
|---|---|
| MPN | LSL14 - EACH |
| SKU | LSL14 - EACH |
| Category | Fasteners & Hardware |
| Weight Capacity (lb.) | Less than 150 |
|---|---|
| Fastener Type | Lag Shields |
| Fastener Material | Metal |
| Interior/Exterior | Exterior |
| Weight Capacity (lb.) | Less than 150 |
|---|---|
| Fastener Type | Lag Shields |
| Fastener Material | Metal |
| Lag screw thread size | 1/4-10 UNC |
| Federal specification | GSA FFS-325C, Group 2, Type 1, Class 1 (long) |
| Compatible lag-screw thread | 1/4-10 UNC |
| Threading and removability | Internally threaded; allows bolt removal for service work |
| Removability and service | Internal threading allows easy bolt removal and service work. |
| Installation torque | Approximately 5 ft.-lbs. |
| Interior/Exterior | Exterior |
|---|---|
| Measurement System | Inches |
| Recommended substrate condition | Long version recommended for soft or weak masonry to add strength to the substrate |
| Anchor seating | Insert the anchor into the hole and tap flush |
| Anchor setting | Insert the anchor into the hole and tap flush. |
| Hole drilling procedure | Drill perpendicular to the work surface; do not ream the hole or allow the drill to wobble. |
| Compatible substrates | Concrete and mortar joints of brick and block walls |
| Hole depth and clearance | Drill at least one anchor diameter deeper than the intended embedment, but no closer than two diameters to the opposite concrete surface. |
| Drill bit requirement | Use solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards. |
| Installation safety | Wear safety glasses and follow the drill manufacturer's instructions. |
| Substrate recommendation | The long version is recommended for soft or weak masonry to add strength to the substrate. |
| Suitable base materials | Concrete, masonry, and mortar joints |
| Corrosion resistance | Corrosion resistant |
| Fixture fastening | Position the fixture, insert the bolt, and tighten. |
| Hole cleaning | Clean the hole with a nylon brush and compressed air. |
| Listed application | Railings |
| Drill bit standard | Use solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards |
| Drill bit diameter | 1/2 in. |
| Length (in.) | 1.5 |
|---|---|
| Thread length | 1 in. |
Added to cart
$150.00 away from free shipping!