Skip to content
Wej-It

Short Lag Screw Shield, 3/8" (LSS38) - Each

0 Reviews
SKU
LSS38 - EACH

The Wej-It LSS38 is a short lag screw shield for 3/8-7 lag screws, made from corrosion-resistant Zamac alloy. It measures 1-3/4 inches long, specifies a 5/8-inch drill-bit diameter, and is listed for concrete and mortar joints in brick and block walls.

  • 3/8-7 Internal Thread
  • Concrete and Masonry Substrates
  • 1-3/4-Inch Length
  • 5/8-Inch Drill-Bit Diameter
  • Corrosion-Resistant Zamac Alloy
  • Removable for Service Work

The Wej-It LSS38 is a short lag screw shield for 3/8-7 lag screws, made from corrosion-resistant Zamac alloy. It measures 1-3/4 inches long, specifies a 5/8-inch drill-bit diameter, and is listed for concrete and mortar joints in brick and block walls.

Product Overview

The Wej-It LSS38 is a short lag screw shield for 3/8-7 lag screws, made from corrosion-resistant Zamac alloy. It measures 1-3/4 inches long, specifies a 5/8-inch drill-bit diameter, and is listed for concrete and mortar joints in brick and block walls.

  • 3/8-7 Internal Thread
  • Concrete and Masonry Substrates
  • 1-3/4-Inch Length
  • 5/8-Inch Drill-Bit Diameter
  • Corrosion-Resistant Zamac Alloy
  • Removable for Service Work

Technical Specifications

Product information and specifications for the selected item.

SKU: LSS38 - EACH

Product Information

BrandWej-It
MPNLSS38 - EACH
SKULSS38 - EACH
CategoryFasteners & Hardware

Key Specs

Fastener TypeLag Shields
Fastener MaterialMetal
Interior/ExteriorExterior

Capacity & Fastener

Fastener TypeLag Shields
Fastener MaterialMetal
Federal specificationGSA FFS-325C, Group 2, Type 1, Class 2C (short)
Federal specification classificationGSA FFS-325C, Group 2, Type 1, Class 2C (short)
Bolt removabilityInternally threaded; allows easy bolt removal and service work.
Lag-bolt size3/8 - 7
Thread size (UNC)3/8-7
Approximate installation torque10 ft.-lbs.

Finish & Use

Interior/ExteriorExterior
Measurement SystemInches
Anchor settingInsert the anchor into the hole and tap it flush
Hole cleaningClean the hole with a nylon brush and compressed air.
Service removabilityAllows easy removability for service work
Substrate recommendationRecommended for harder masonry to reduce drilling time
Substrate compatibilityDesigned for lag screws in concrete and the mortar joints of brick and block walls.
Fixture fasteningPosition the fixture, insert the bolt, and tighten
Drill-bit requirementUse solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards.
Corrosion resistanceCorrosion resistant
Suitable base materialsConcrete, masonry, and mortar joints
Substrate selectionRecommended for harder masonry materials to reduce drilling time.
Hole preparationDrill perpendicular to the work surface; do not ream the hole or allow the drill to wobble.

Dimensions & Weight

Length (in.)1.75
Minimum embedment depth in clay brick masonry1-3/4 in.
Minimum embedment depth in hollow concrete masonry1-1/2 in.
Drill-bit diameter5/8 in.
Drill-hole depth and clearanceDrill at least one anchor diameter deeper than intended embedment, while keeping the hole at least two diameters from the opposite concrete surface.
Minimum embedment depth in normal-weight concrete1-3/4 in.

Product Documents

Your cart

0 products 0 units

Your cart is empty.

Add products as you browse, then review them here.